Constellation, le dépôt institutionnel de l'Université du Québec à Chicoutimi

Article publié dans une revue avec comité d'évaluation

Agbe, Henry, Sarkar, Dilip K. et Chen, X-Grant. (2020). Tunable Superhydrophobic Aluminum Surfaces with Anti-Biofouling and Antibacterial Properties. Coatings, 10, (10), p. 982.

Andrade, Alexandre Gonçalves, Beaudin, Steve, Tremblay, Eric, Cloutier-Poirier, François, Damasceno, Hilcker Scopel, Gavazza Junior, Luiz Carlos, Dion, Lukas et Faubert, Patrick. (2026). Novel roller screening technology for enhanced reduction of fine particles in iron ore fired pellets production. Minerals Engineering, 247, (e110476),

Arroyo Fernandez, Oscar Henry, Fofana, Issouf, Jalbert, Jocelyn et Ryadi, Mohamed. (2015). Relationships between methanol marker and mechanical performance of electrical insulation papers for power transformers under accelerated thermal aging. IEEE Transactions on Dielectrics and Electrical Insulation, 22, (6), p. 3625-3632.

Bolouri, Amir, Liu, Kun et Chen, X-Grant. (2016). Effects of iron-rich intermetallics and grain structure on semisolid tensile properties of Al-Cu 206 cast alloys near solidus temperature. Metallurgical and Materials Transactions A,

Chehouri, Adam, Younès, Rafic, Khoder, Jihan, Perron, Jean et Ilinca, Adrian. (2017). A selection process for genetic algorithm using clustering analysis. Algorithms, 10, (4), p. 123.

Chehouri, Adam, Younès, Rafic, Perron, Jean et Ilinca, Adrian. (2016). A constraint-handling technique for genetic algorithms using a violation factor. Journal of Computer Science, 12, (7), p. 350-362.

Eke, Samuel, Clerc, Guy, Aka-Ngnui, Thomas et Fofana, Issouf. (2019). Transformer condition assessment using Fuzzy C-means clustering techniques. IEEE Electrical Insulation Magazine, 35, (2), p. 47-55.

Fiset, Mathieu, Bastien, Josée et Mitchell, Denis. (2017). Methods for shear strengthening of thick concrete slabs. Journal of Performance of Constructed Facilities, 31, (3), p. 1-10.

Hidouri, Slah, Jafari, Reza, Fournier, Claire, Girard, Catherine et Momen, Gelareh. (2022). Formulation of nanohybrid coating based on essential oil and fluoroalkyl silane for antibacterial superhydrophobic surfaces. Applied Surface Science Advances, 9, e100252.

Ibrahim, Hussein, Ghandour, M., Dimitrova, Mariya Hristova, Ilinca, Adrian et Perron, Jean. (2011). Integration of wind energy into electricity systems : technical challenges and actual solutions. Energy Procedia, 6, p. 815-824.

Jafari, Reza et Farzaneh, Masoud. (2011). Fabrication of superhydrophobic nanostructured surface on aluminum alloy. Applied Physics A. Materials Science & Processing, 102, (1), p. 195-199.

Jafari, Reza et Farzaneh, Masoud. (2012). A simple method to create superhydrophobic aluminium surfaces. Materials science forum, 706-709, p. 2874-2879.

Jafari, Reza, Farzaneh, Masoud et Menini, Richard. (2010). Superhydrophobic and icephobic surfaces prepared by RF-sputtered polytetrafluoroethylene coatings. Applied surface science, 257, (5), p. 1540-1543.

Jamali, Abdeslam, Snaiki, Reda et Rahem, Ahmed. (2025). Towards accurate ice accretion and galloping risk maps for Quebec: A data-driven approach. Cold Regions Science and Technology, 233, e104460.

Jeon, Gwanggil et Chehri, Abdellah. (2021). Computing techniques for environmental research and public health. International Journal of Environmental Research and Public Health, 18, (18), e9851.

Jeon, Gwanggil et Chehri, Abdellah. (2021). Special issue on applied computational intelligence. Concurrency and Computation: Practice and Experience, 33, (22),

Kijewski-Correa, Tracy, Taflanidis, Alexandros, Vardeman, Charles, Sweet, James, Zhang, Jize, Snaiki, Reda, Wu, Teng, Silver, Zachariah et Kennedy, Andrew. (2020). Geospatial environments for hurricane risk assessment: Applications to situational awareness and resilience planning in New Jersey. Frontiers in Built Environment, 6, p. 549106.

Liu, Kun et Chen, X-Grant. (2015). Development of Al-Mn-Mg 3004 alloy for applications at elevated temperature via dispersoid strengthening. Materials and Design, 84, p. 340-350.

Liu, Kun et Chen, X-Grant. (2015). Evolution of intermetallics, dispersoids and elevated-temperature properties at various Fe contents in Al-Mn-Mg 3004 alloys. Metallurgical and Materials Transactions B,

Liu, Kun, Ma, Hezhaoye et Chen, X-Grant. (2017). Enhanced elevated-temperature properties via Mo addition in Al-Mn-Mg 3004 alloy. Journal of alloys and compounds, 694, p. 354-365.

Maghsoudi, Khosrow, Momen, Gelareh, Jafari, Reza et Farzaneh, Masoud. (2018). Direct replication of micro-nanostructures in the fabrication of superhydrophobic silicone rubber surfaces by compression molding. Applied Surface Science, 458, p. 619-628.

Maghsoudi, Khosrow, Momen, Gelareh, Jafari, Reza et Farzaneh, Masoud. (2019). Rigorous testing to assess the self-cleaning properties of an ultra-water-repellent silicone rubber surface. Surface and Coatings Technology, 374, p. 557-568.

Otis, Martin J.-D., Nguyen-Dang, Thien-Ly, Laliberte, Thierry, Ouellet, Denis, Laurendeau, Denis et Gosselin, Clément. (2009). Cable tension control and analysis of reel transparency for 6-DOF haptic foot platform on a cable-driven locomotion interface. International Journal of Electrical and Electronics Engineering, 3, (1), p. 16-29.

Oumert, L. Safiddine, Boucherit, Ahmed, Zafour, Amel Hadj-Ziane et Fofana, Issouf. (2018). Comparative study of the degradation rate of new and regenerated mineral oils following electrical stress. IET Generation, Transmission and Distribution, 12, (21), p. 5891-5897.

Pelletier, Anthony J., Faubert, Patrick, Lafond, Jean, Bertrand, Normand, Legault, Jean, Ouimet, Rock, Pelster, David E., Pichette, André, Ziadi, Noura et Paré, Maxime C.. (2025). Conventional and industrial by-product fertilization do not induce greenhouse gas emissions in sandy soils under wild lowbush blueberry cropping in eastern Canada. Geoderma Regional, 43, e01024.

Perron, Alexandre, Kiss, László et Verreault, René. (2006). A multifibre optic sensor to measure the liquid film thickness between a moving bubble and an inclined solid surface. Measurement Science and Technology, 17, (6), p. 1594-1600.

Perron, Jean. (2024). Hubble Tension Explanation from This Cosmological Model AΛΩ (Slow Bang Model, SB). Journal of High Energy Physics, Gravitation and Cosmology, 10, (1), p. 106-125.

Perron, Jean. (2025). Quantum Klein-Gordon Equation of a Bosonic Particle in an Expanding Volume: CMB Photon Predicts the Age of the Universe (76.4 Gy) and the Observed Age (13.8 Gy) with Special Relativity. Journal of high energy physics, graviation and cosmology, 11, (3), p. 701-713.

Rakhmonov, Jovid, Liu, Kun, Pan, Lei, Breton, Francis et Chen, X-Grant. (2020). Enhanced mechanical properties of high-temperature-resistant Al–Cu cast alloy by microalloying with Mg. Journal of Alloys and Compounds, 827, (154305),

Saha, Sudeshna, Kocaefe, Duygu, Boluk, Yaman, Mshvildadze, Vakhtang, Legault, Jean et Pichette, André. (2013). Boreal forest conifer extracts : potential natural additives for acrylic polyurethane coatings for the protection of heat-treated jack pine. Journal of Coatings Technology and Research, 10, (1), p. 109-122.

Segning, Colince Meli, Ezzaidi, Hassan, da Silva, Rubens Alexandre et Ngomo, Suzy. (2021). A neurophysiological pattern as a precursor of work-related musculoskeletal disorders using EEG combined with EMG. International Journal of Environmental Research and Public Health, 18, (4), p. 2001.

Snaiki, Reda et Wu, Teng. (2018). An analytical framework for rapid estimate of rain rate during tropical cyclones. Journal of Wind Engineering and Industrial Aerodynamics, 174, p. 50-60.

Snaiki, Reda et Wu, Teng. (2020). Hurricane hazard assessment along the United States northeastern coast: Surface wind and rain fields under changing climate. Frontiers in Built Environment, 6, p. 573054.

Snaiki, Reda et Wu, Teng. (2019). Knowledge-enhanced deep learning for simulation of tropical cyclone boundary-layer winds. Journal of Wind Engineering and Industrial Aerodynamics, 194, p. 103983.

Snaiki, Reda et Wu, Teng. (2017). A linear height-resolving windfield model for tropical cyclone boundary layer. Journal of Wind Engineering and Industrial Aerodynamics, 171, p. 248-260.

Snaiki, Reda et Wu, Teng. (2019). Modeling rain-induced effects on boundary-layer wind field of tropical cyclones. Journal of Wind Engineering and Industrial Aerodynamics, 194, p. 103986.

Snaiki, Reda et Wu, Teng. (2017). Modeling tropical cyclone boundary layer: Height-resolving pressure and wind fields. Journal of Wind Engineering and Industrial Aerodynamics, 170, p. 18-27.

Snaiki, Reda et Wu, Teng. (2020). Revisiting hurricane track model for wind risk assessment. Structural Safety, 87, p. 102003.

Snaiki, Reda et Wu, Teng. (2018). A semi-empirical model for mean wind velocity profile of landfalling hurricane boundary layers. Journal of Wind Engineering and Industrial Aerodynamics, 180, p. 249-261.

Snaiki, Reda, Wu, Teng, Whittaker, Andrew S. et Atkinson, Joseph F.. (2020). Hurricane wind and storm surge effects on coastal bridges under a changing climate. Transportation research record, 2674, (6), p. 23-32.

Vaidis, Maxime et Otis, Martin J.-D.. (2020). Toward a robot swarm protecting a group of migrants. Intelligent Service Robotics, 13, p. 299-314.

Vazirinasab, E., Maghsoudi, Khosrow, Jafari, Reza et Momen, Gelareh. (2020). A comparative study of the icephobic and self-cleaning properties of Teflon materials having different surface morphologies. Journal of Materials Processing Technology, 276, p. 116415.

Verreault, Antoine, Cicek, Paul-Vahé et Robichaud, Alexandre. (2026). A lean noise-canceling SMASH Delta-Sigma ADC in 65-nm CMOS. IEEE Transactions on Circuits and Systems I: Regular Papers, 73, (6), p. 3861-3874.

Verreault, Antoine, Cicek, Paul-Vahé et Robichaud, Alexandre. (2024). Oversampling ADC: A review of recent design trends. IEEE Access, 12, p. 121753-121779.

Villemure, Félix-Antoine, Fiset, Mathieu, Bastien, Josée, Mitchell, Denis et Fournier, Benoit. (2019). Behavior of epoxy bonded bars in concrete affected by alkali-silica reaction. ACI Materials Journal, 116, (6), p. 179-191.

Chapitre de livre

Cerclet, Tobie, Guérin, Julie Élize, Savard, Véronique, Zarrougui, Ramzi, Simard, Marie-Christine, Côté, Marie, Boucher, Jean-François et Chesnaux, Romain. (2023). Cover layer design based on bauxite residue for ecological restoration: A Northern climatic zone study case—geochemical phase. Dans Abbasi, B, Parshley, J, Fourie, A et Tibbett, M (dir.), Mine Closure 2023: Proceedings of the 16th International Conference on Mine Closure. (p. 1-14). Perth : Australian Centre for Geomechanics.

Otis, Martin J.-D., Duchaine, Vincent, Billette, Greg, Perreault, Simon, Gosselin, Clément et Laurendeau, Denis. (2010). Cartesian control of a cable-driven haptic mechanism. Dans Hosseini Zadeh, Mehrdad (dir.), Advances in Haptics. (p. 75-102). New York : InTech.

Villeneuve, Claude, Riffon, Olivier, Segers, Ian et Tremblay, David. (2017). Mines et développement durable, comment aborder la quadrature du cercle? Dans Rouleau, Alain et Gasquet, Dominique (dir.), L’industrie minière et le développement durable : une perspective internationale francophone. (p. 5-29). Points de repère. Québec : Institut de la Francophonie pour le développement durable (IFDD).

Matériel de conférence

Brassard, Jean-Denis, Sarkar, Dilip K. et Perron, Jean. (2011). Surface modifications and functionalization of Oxyde nanoparticules for superhydrophobic applications. Dans : Thermec , Québec, Canada..

Chehri, Abdellah. (2021). Contention Based Medium Access Control Protocol for Point-To-Multipoint Backhaul Networks in the 3.65 GHz Band. Dans : 2021 IEEE International Symposium on Antennas and Propagation and USNC-URSI Radio Science Meeting , 4-10 December 2021, Marina Bay Sands, Singapore.

Chen, Sinan, Liu, Kun et Chen, X-Grant. (2019). Elevated-temperature low-cycle fatigue behaviors of Al-Si 356 and 319 foundry alloys. Dans : TMS-Light Metals 2019 , March 10-14, San Antonio, Texas.

Dimitrova, Mariya Hristova, Ibrahim, Hussein, Fortin, Guy, Perron, Jean et Ilinca, Adrian. Numerical simulation of the wind energy production losses due to icing. Dans : WINDPOWER 2011 Conference and exhibition , May 22-25, 2011, Anaheim, USA.

Fiset, Mathieu, Bastien, Josée et Mitchell, Denis. (2014). Experimental and analytical studies of strengthening using drilled-in bonded shear reinforcement. Dans : 15th International Conference Sructural Faults & Repair-2014 , 8th – 10th July 2014, Edinburgh, Scotland.

Li, S., Snaiki, Reda et Wu, Teng. (2020). Active simulation of transient wind fields in a multiple-fan wind tunnel via deep reinforcement learning. Dans : Engineering Mechanics Institute Conference , May 26-29, 2020, New York, United States.

Liu, Kun, Cao, X., Bolouri, Amir et Chen, X-Grant. (2019). Effect of Fe-rich intermetallics on tensile behavior of Al-Cu 206 cast alloys at solid and near-solid states. Dans : TMS-2019 Shape Casting: 7th International Symposium celebrating Prof. John Campbell’s 80 th Birthday , March 10-14, San Antonio, Texas.

Snaiki, Reda et Wu, Teng. (2017). Dynamic interaction of wind and rain fields in the boundary layer of a tropical cyclone. Dans : Proceedings of Engineering Mechanics Institute Conference 2017 (EMI 2017) , June 4-7, 2017, San Diego, CA, USA.

Snaiki, Reda et Wu, Teng. (2021). Hurricane risk assessment of offshore wind turbines under a changing climate scenario. Dans : IABSE Congress : Structural Engineering for Future Societal Needs , 22 to 24 September 2021, Ghent, Belgique.

Snaiki, Reda et Wu, Teng. (2018). An improved methodology for risk assessment of tropical cyclones under changing climate. Dans : Proceedings of 33rd Conference on Hurricanes and Tropical Meteorology , April 16 -20, 2018, Ponte Verda, FL, USA.

Snaiki, Reda et Wu, Teng. (2019). Knowledge-enhanced deep learning for simulation of extratropical cyclone wind risk. Dans : 15th International Conference on Wind Engineering (ICWE15) , September 1-6, 2019, Beijing, China.

Snaiki, Reda et Wu, Teng. (2019). A knowledge-enhanced deep learning for simulation of idealized storm surge. Dans : Proceedings of Engineering Mechanics Institute Conference 2019 (EMI 2019) , September 1-6, 2019, Pasadena, California, USA.

Snaiki, Reda et Wu, Teng. (2019). Knowledge-enhanced deep learning for simulation of tropical cyclone boundary layer winds. Dans : Proceedings of 15th International Conference on Wind Engineering (ICWE15) , September 1-6, 2019, Beijing, China.

Snaiki, Reda et Wu, Teng. (2018). A new boundary layer wind field model for landfalling hurricanes. Dans : Proceedings of 10th International Conference on Urban Climate/14th Symposium on the Urban Environment , August 6-10, 2018, New York, NY, USA.

Snaiki, Reda et Wu, Teng. (2021). Reduced-order modeling with efficient data assimilation: A real-time prediction framework for wind-turbine wakes. Dans : 13th International Conference on Structural Safety & Reliability , 2021, Tongji University, Shanghai, China.

Snaiki, Reda et Wu, Teng. (2016). A simplified analytical wind‐field model for hurricane boundary layer. Dans : Proceedings of Engineering Mechanics Institute Conference 2016 (EMI 2016)s & Reliability Conference 2016 (PMC 2016) , May 22-25, 2016, Nashville, TN, USA..

Snaiki, Reda et Wu, Teng. (2019). A simplified dynamic system for estimating hurricane supergradient winds. Dans : Proceedings of 15th International Conference on Wind Engineering (ICWE15) , September 1-6, 2019, Beijing, China.

Snaiki, Reda et Wu, Teng. (2016). Temperature and moisture effects on the hurricane wind field based on a simplified model. Dans : Proceedings of Engineering Mechanics Institute Conference 2016 (EMI 2016)chanics & Reliability Conference 2016 (PMC 2016) , May 22-25, 2016, Nashville, TN, USA..

Snaiki, Reda et Wu, Teng. (2016). Temperature and moisture effects on the tropical cyclone boundary layer: pressure and wind fields. Dans : Proceedings of 8th International Colloquium on Bluff-Body Aerodynamics and its Application (BBAAVIII) , June 7-11, 2016, Boston, USA.

Snaiki, Reda et Wu, Teng. (2017). A theoretical model for rapid estimates of rainfall during tropical cyclones. Dans : Proceedings of 13th Americas Conference on Wind Engineering (13ACWE) , May 21-24, 2017, Gainesville, FL, USA.

Snaiki, Reda, Wu, Teng, Whittaker, Andrew S. et Atkinson, Joseph F.. (2020). Hurricane wind and storm surge effects on coastal bridges under a changing climate. Dans : Proceedings of Transportation Research Board (TRB) 99th Annual Meeting , Jan 12-16, 2020, Washington, D.C, USA..

Thèse ou mémoire de l'UQAC

Adekunle, Andrew Adewunmi. (2025). Multiclass Fault Diagnosis in Power Transformers Using Dissolved Gas Analysis and Grid Search-Optimized Machine Learning. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Agouassi, Tetchi Moïse Junior. (2025). Comportement de formation de gaz dans les liquides biodégradables : influence de la composition chimique. Thèse de doctorat, Université du Québec à Chicoutimi.

Andoh, Marc Alain. (2025). Développement d’un modèle thermoélectrique numérique de formation des bandes sèches à la surface des isolateurs composites pollués. Thèse de doctorat, Université du Québec à Chicoutimi.

Charpentier, Claire. (2025). Outils de détermination des critères de performance des produits antigivre et dégivrants pour piste d'aéroport afin de définir les taux d'épandage optimaux. Thèse de doctorat, Université du Québec à Chicoutimi.

Daadaa, Marouan. (2025). Performance structurale des poutres en béton armé renforcées en cisaillement par la technique ETS : Influence des charges préexistantes et du type de matériau. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Dastjerdy, Behzad. (2025). Evaluation of effects of geomechanical parameters and in-situ stress on rockburst occurrence in deep excavations. Thèse de doctorat, Université du Québec à Chicoutimi.

Fousseni, Chourik. (2026). Estimation du temps de conduite d’un véhicule électrique entre deux états de charge à l’aide des algorithmes d’apprentissage automatique. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Gaudreault, Noémie. (2024). Dynamiques saisonnières de la méthanotrophie et des gaz à effet de serre dans un lac boréal. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Goharshenasmoghadam, Saba. (2024). Investigation and optimization of effective parameters for fabrication of novel anti-icing coatings containing ionic liquids. Thèse de doctorat, Université du Québec à Chicoutimi.

Hossain, A S M Fahad. (2025). Seismic microzonation mapping based on nonlinear site response analysis: methodology development and application to Saguenay, Quebec. Thèse de doctorat, Université du Québec à Chicoutimi.

Jacob, Sarah. (2024). Determination of geotechnical characteristics of sensitive clay of Lac-Saint-Jean in the objective of prediction of retrogressive landslides. Thèse de doctorat, Université du Québec à Chicoutimi.

Jafari Aminabadi, Mohammad. (2025). Nonlinear programming for stochastic short-term hydropower operations planning considering uncertain prices. Thèse de doctorat, Université du Québec à Chicoutimi.

Karnati, Vineeth Reddy. (2025). Influence de la géométrie des joints et de la rugosité de surface sur les pressions hydrauliques et la stabilité des blocs dans les évacuateurs de crues à l’échelle de laboratoire. Thèse de doctorat, Université du Québec à Chicoutimi.

Keshavarzi, Samaneh. (2023). In-depth study of ice nucleation and adhesion on structured hydrophobic and superhydrophobic surfaces. Thèse de doctorat, Université du Québec à Chicoutimi.

Muhammed, Musa. (2025). Tribological performance enhancement of AlTiN/AlTiCrN-based physical vapour deposition coatings for wood-processing application. Thèse de doctorat, Université du Québec à Chicoutimi.

Nabli, Salma. (2024). Optimisation du désassemblage en collaboration humain-robot à l’aide des algorithmes génétiques : application au reconditionnement des batteries de véhicules électriques. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Ngombe, Othniel Glodie Dominique. (2026). Origine et migration des eaux souterraines du Bouclier Canadien révélées à partir de la modélisation numérique et des traceurs géochimiques. Thèse de doctorat, Université du Québec à Chicoutimi.

Obebe, Esther Ogwa. (2025). Amélioration de la stabilité à l’oxydation des esters naturels par l’ajout d’antioxydants à l’aide d’une analyse statistique multi-réponses pour les applications dans les transformateurs. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Oparanti, Samson Okikiola. (2025). Huile de canola améliorée par des additifs écologiques pour l’isolation des transformateurs en climat froid. Thèse de doctorat, Université du Québec à Chicoutimi.

Pourkhorshid, Esmaeil. (2025). Aluminum alloys for additive manufacturing: towards higher strength alloys. Thèse de doctorat, Université du Québec à Chicoutimi.

Sénéchal, David. (2025). Prétraitement thermique et dissolution incongruente de l'apatite du Lac à Paul : implications pour la biodisponibilité du phosphore et la séquestration du carbone. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Shalaby, Dena. (2023). Développement d’un béton géopolymère à base de résidu de bauxite et de cendre volante pour des éléments architecturaux. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Taylor, Wasuita. (2025). Geology of the Western Part of the Porphyry Zone, Douay Gold Deposit: Genesis of Archean ‘syenite-associated’ mineralization in the Northern Abitibi Greenstone Belt. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Tenesso Mefeuya, Hervé. (2025). Optimisation de la recharge des véhicules électriques (VÉ) dans les sites hors réseau. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Thota, Jayasree. (2024). Esters synthétiques comme alternatives à l'huile minérale pour transformateurs destinés aux régions froides. Thèse de doctorat, Université du Québec à Chicoutimi.

Toure, Hamadoun. (2026). Optimisation topologique des structures en 3D en tenant compte du flambage : Cas d’une passerelle en aluminium. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Tremblay, Xavier. (2025). Solidification of hypoeutectic Al-Si alloys during high-pressure vacuum die-casting (HPVDC) of thin-walled components & the influence of subsurface microstructure variations on bending ductility. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Tripathy, Rohini Nandan. (2026). Optimisation du lit résistif dans cuves d'électrolyse pendant la phase de préchauffage. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Verreault, Antoine. (2025). Conception d’un convertisseur analogique-numérique à haute précision et basse consommation de puissance avec la technologie CMOS 65 nm. Mémoire de maîtrise, Université du Québec à Chicoutimi.

Thèse ou mémoire d'autres institutions

Otis, Martin J.-D.. (2004). Développement d'un système de propulsion pour un biomicrorobot hexapode avec un ionomère perfluorosulfonique. Mémoire de maîtrise, Université de Sherbrooke.